How to Clear a Paper Jam in a Shredder
To clear a paper jam in a shredder, switch it off, unplug it, remove loose paper, and use reverse only as directed by the manual. Never force paper through the cutters or reach into the feed opening while the shredder has power.
On this page (8 sections)
- What should you do first when a shredder jams?
- How do you use reverse to release stuck paper?
- How do you remove paper that will not come out?
- How can you prevent another paper jam?
- How do run time and the bin affect paper jams?
- How should you care for a shredder after clearing a jam?
- When should you replace or service a shredder?
- What is the safest way to clear a paper jam in a shredder?
To clear a paper jam in a shredder, switch it off, unplug it, remove loose paper, and use the reverse setting only as the manual directs. Never reach into the cutters while the shredder is connected to power, and do not force paper that will not move.
A jam often starts when too many sheets enter at once, paper folds at the feed opening, or the bin is too full. A careful reset and a small test stack can restore normal shredding without damaging the cutters or motor.
Start by stopping the feed as soon as paper slows, wrinkles, or bunches near the opening. Keep your hands and any tools clear until the power is off and the plug is out of the socket.
Look at the paper that is still above the feed opening and pull it gently in the direction it entered. Avoid twisting the sheet, because a torn edge can leave small scraps behind for the cutters to catch again.
Check the waste bin next, since a packed bin can block fresh shreds and make the next sheets look stuck. Empty the bin if it is full, push it back into place, and make sure any door or bin sensor is seated correctly.
If the motor feels warm, give it time to cool before you try another cycle. Repeated switching on and off can add heat without clearing the blockage, and it makes later diagnosis harder.
Use the reverse control only in a brief movement and only when the manual allows it for your model. Stop right away if the paper does not release, and do not alternate quickly between forward and reverse to force it through.
Once the visible paper is out, empty the bin and inspect the cutter area from above without reaching inside. Remove only scraps you can reach safely, and leave anything deeper for the method your manual approves.
Test the machine with just a few flat sheets after it has cooled and the bin is empty. Feed the pages one after another so you can watch the entry, listen for strain, and stop early if the same problem returns.
What should you do first when a shredder jams?
Stop feeding paper immediately, switch the shredder off, and unplug it. Keep your hands, tools, and loose clothing away from the paper opening until the machine is disconnected.
Remove any paper that is loose above the feed opening. Pull it slowly in the direction it entered, without twisting the sheet or pushing fingers toward the cutters.
Check whether the waste bin is full or out of position. A full bin can block shredded pieces and make new paper appear stuck, so empty and reseat it before trying another cycle.
If the motor feels hot, wait for it to cool fully. Do not bypass an automatic shutoff or keep switching the machine on and off to force it through a jam.
How do you use reverse to release stuck paper?
Use the reverse switch briefly to move paper back toward the feed opening. Keep the opening clear, stand to the side of the machine, and stop as soon as the paper begins to release.
Some shredders use reverse as part of their jam-clearing controls. The Amazon Basics 24-Sheet Cross Cut High Security has a 4-mode switch with auto, off, reverse, and forward, plus anti-jam auto reverse.

Its reverse and anti-jam functions can help release stuck paper, while the 24-sheet capacity suits larger home-office batches.
See it on AmazonAfter reversing, switch the shredder off and unplug it again before pulling out remaining scraps. Do not alternate rapidly between forward and reverse if the paper is tightly packed.
If reverse does not move the jam, stop. Forcing the controls can strain the motor, and sharp cutters may remain hidden behind the paper.
How do you remove paper that will not come out?
Unplug the shredder before removing paper that remains lodged in the feed opening. Use only a tool approved by the manual, and work from the accessible top edge rather than pushing anything deep into the cutter area.
Pull out small pieces one at a time. If the sheet tears, remove the visible scraps before trying another reverse cycle.
Never use a knife, screwdriver, scissors, or metal object to dig into the cutters. These tools can damage the cutting assembly and may slip toward your hand.
Check the underside of the shredder head only if the manual allows you to remove it safely. Keep the head supported and do not operate the machine while any cover or bin sensor is disconnected.
How can you prevent another paper jam?
Feed fewer flat sheets than the maximum whenever a page stack is thick, folded, or mixed with inserts. A stated sheet limit is a maximum for a specific paper type, not a reason to force every stack through at once.
Remove paper clips, staples, adhesive labels, and folded corners when the shredder does not support them. Keep envelopes, laminated sheets, and other unusual materials out unless the manual specifically permits them.
The Fellowes Powershred 99Ci 18-Sheet 100% Jam-Proof Heavy handles up to 18 sheets per pass and also shreds staples, credit cards, paper clips, CDs/DVDs, and junk mail. Fellowes also includes SafeSense protection that stops shredding when hands touch the paper opening.

Its 100% Jam-Proof design and SafeSense protection suit shared home or office spaces where repeated paper feeding is common.
See it on AmazonFor a closer look at that model, see our Fellowes 99ci paper shredder reviews. If jam resistance is your main concern, compare the best quality paper shredder with jam proof options before replacing a machine that jams often.
How do run time and the bin affect paper jams?
Respect the shredder's run and cool-down limits, and empty the bin before shredded paper blocks the cutters. A machine that overheats or operates against a packed bin may stop even when no large sheet is visible.
The Amazon Basics model runs for up to 40 minutes before a 50-minute cool-down period. It has a 7-gallon pullout bin and indicators for bin full, door open, overload, overheat, and power.
The Fellowes 99Ci runs for up to 30 minutes and has a 9-gallon pullout bin with a bin-full indicator. Its cross-cut output measures 5/32 by 1-1/2 inches, so the bin can fill with many small pieces during a long session.
Keep the bin seated correctly after emptying it. If the door or bin indicator remains active, switch off and unplug the shredder before checking for scraps around the sensor area.
How should you care for a shredder after clearing a jam?
Clean accessible paper dust and follow the manual's cutter-care instructions after the jam is gone. Do not spray aerosol products in or around the shredder, and keep liquids away from the motor and electrical parts.
Use the care method approved for your model. Our Paper Shredder Maintenance & Oiling Guide explains how regular maintenance can support smoother feeding.
Run a short test with a small number of flat sheets. Listen for unusual sounds, watch for new paper buildup, and stop if the motor struggles or the paper feeds unevenly.
If you need a smaller machine for light tasks, compare the best small paper shredder. For a broader office setup, our guide to desktop printers covers other office-machine decisions that often sit beside shredding.
Can a jammed shredder still handle cards or discs?
Do not test cards, discs, or other materials until ordinary paper feeds normally again. Once the machine works, use only the dedicated slot or material type the manual permits.
The Amazon Basics model includes separate support for CDs, DVDs, credit cards, staples, and small paper clips. Its credit-card guidance says to use the dedicated slot one card at a time and not to shred metallic credit cards.
The Fellowes 99Ci supports staples, credit cards, paper clips, CDs/DVDs, and junk mail. Even when a shredder supports these items, remove excess paper and feed one suitable item at a time when the instructions require it.
When should you replace or service a shredder?
Stop using the shredder if it jams while empty, smells hot after cooling, makes grinding sounds, or will not reverse and forward normally. Continued operation can turn a simple paper blockage into a motor or cutter problem.
Check the manual for approved service steps and support options. Do not open the motor housing or defeat safety sensors unless a qualified service provider instructs you to do so.
Repeated jams can also point to heavier use than the machine was built for. A model rated for larger batches or longer run times may suit a busy desk better than a compact unit that keeps cooling down.
If the machine works after careful clearing but jams repeatedly, reduce the stack size and improve routine care first. Persistent problems after those changes are a reason to compare a jam-resistant replacement.
What is the safest way to clear a paper jam in a shredder?
Unplug the machine, remove loose paper, reverse briefly if allowed, clear remaining scraps with the approved method, and test with a small stack. Empty the bin and allow the motor to cool before returning to normal use.
Choose the Amazon Basics model if its 24-sheet capacity, 7-gallon pullout bin, and 40-minute run time fit your larger home-office batches. Choose the Fellowes 99Ci if its 18-sheet capacity, 30-minute run time, SafeSense protection, and 100% Jam-Proof design better match a shared workspace.
Use these steps whenever you face a paper jam in a shredder, and keep the How to Line Desk Drawers With Contact Paper guide nearby for another practical office organization project.
Frequently asked questions
How do you clear a paper jam in a shredder?
Switch the shredder off and unplug it before removing loose paper. Follow the manual's reverse and forward instructions, pull out accessible scraps without forcing them, empty the bin, and let the motor cool before testing with a small stack.
Can you use reverse to clear a shredder jam?
Yes, reverse can help release paper if the shredder supports that function, but use it only with the feed opening clear of hands and after following the manual. Switch off and unplug the machine before removing any paper that remains stuck.
Why does my paper shredder keep jamming?
Repeated jams often come from feeding too many sheets, folded or damaged paper, a full bin, or cutters that need care. Stay below the shredder's sheet limit, feed flat pages, empty the bin, and follow the manual's cleaning and oiling instructions.
How can I prevent a paper jam in a shredder?
Prevent jams by feeding flat paper in small stacks, removing thick clips or unsuitable items, keeping the bin from filling too high, and observing the run and cool-down limits. Regular care also helps the cutters move paper more freely.
About this guide: Our look at clearing a paper jam in a shredder draws on maker specs, materials and what owners report. See how we research.



